| My belt cp v2 wont leave the ground | |
|
|
Author | Message |
---|
blazemob
| Subject: My belt cp v2 wont leave the ground Mon Mar 30, 2009 10:40 pm | |
| was flying fine all day, then i had to charge a battery went back out boom was wobbaling a lil bit not bad though so adjusted the delay a lil fixed that problem, but now it wont leave the ground even at full throttle | |
|
| |
Fatdaddy
| Subject: Hov.Pitt Tue Mar 31, 2009 12:13 am | |
| | |
|
| |
blazemob
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 12:17 am | |
| the stock tx that came with it from esky | |
|
| |
Fatdaddy
| Subject: knobs Tue Mar 31, 2009 12:24 am | |
| Did you check the knobs on top? the hov.pit I think it is called. The one on the left, by Idle up. set at zero? | |
|
| |
blazemob
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 12:25 am | |
| yea there both set at zero | |
|
| |
Donnie D
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 12:58 am | |
| Try unplugging the motor, turn on transmitter, plug in heli, and see what happens with the swash and blade pitch when you move the throttle stick up. Donnie D | |
|
| |
blazemob
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 1:10 am | |
| i know this sounds stupied but wich wires do i unplug lol here | |
|
| |
Donnie D
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 1:25 am | |
| There are 3 wires that run from the ESC to the motor. A red , a black and a blue one. about half way the length if them is a bullet connector, looks like the wire is thicker there. You can pull the connector apart there. I can be hard to pull apart, but it will. Anyway, disconnect any 2 of them there. This will allow the servos to operate without the motor running.
Again,
1. unplug motor
2. turn on transmitter
3. plug in helicopter
4. move throttle up and down and see what happens with the swash and blade pitch
BE SURE to UNPLUG heli from battery before you plug the motor back up when you finish.
Hope this helps
Donnie D | |
|
| |
Nuttcaze Admin
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 11:00 am | |
| what the heck did you do to your heli Brad?? When you hit yourself in the leg with it the other day did any linkages pop off or break? | |
|
| |
blazemob
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 11:39 am | |
| no they all seem to be fine it only knicked my leg lol but i had it up hovering after that | |
|
| |
blazemob
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 12:42 pm | |
| still no luck jus bounces around on the ground | |
|
| |
blazemob
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 1:38 pm | |
| welp good news i got it back in the air bad news is though i was hovering it around. came down for my landing skids hit and over it went only damage i see is i need a new fly bar,blades and the thing that holds the blade seems bent | |
|
| |
Nuttcaze Admin
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 2:55 pm | |
| | |
|
| |
blazemob
| Subject: Re: My belt cp v2 wont leave the ground Tue Mar 31, 2009 6:32 pm | |
| i flipped the gyro switch down instead of up worked wounders lol | |
|
| |
Sponsored content
| Subject: Re: My belt cp v2 wont leave the ground | |
| |
|
| |
| My belt cp v2 wont leave the ground | |
|